All about frames
The height of the frames is roughly the 1/2" or 1.25cm shorter than the height of the
packs.
What is the height of the frames?
Yes, that’s exactly why Atlas Packs are the best camera bags for travel. You can easily
remove the frame on the Adventure Pack by unzipping the velcro. On the Athlete Pack
you may need a tool that offer some leverage as the frame is help in place via pressure
tabs.
Can frames be easily removed from packs to bring the height down for airline travel?
The Athlete Pack frames can be reduced. Adventure frames cannot. Athlete frames can
be cut down a maximum of around 3/4" without compromise to pack or carry.
Can frames be made shorter?
Generally speaking you should not need to have to hand bend the
frame, but should your specific use case require it, I would advise doing
so with the pack on the ground and facing away from you. Have the top
lid flipped up and over so you can clearly grab and see the frame. Make
sure to push evenly on both sides and the golden rule is a little goes a
long way.
Again, only do this after all the other adjustments are finalized. This
should be a micro adjustment only.
Can the frame be hand bend for better fit?
The Adventure frame is a full surround and cannot be reduced. For the Adventure the
height of the frame is the same for both medium and large. The back panel length is
what determines the torso length.
Why can’t Adventure frames be made shorter?
the large Athlete Pack includes a set of lower “travel frame flaps” that
allow for the installation of a smaller “Travel Frame”. This brings the
height of the large Athlete Pack down to roughly 20".
This frame is intended for travel and not for daily use. With this frame
installed the load lifters on the pack can no longer activate and there is
less support even with the hip belt.
What is the Travel frame for the large Athlete Pack?
Stand the pack up and face the front away. Unzip the backpanel zipper such that only
the top is open (and a bit of the side). The frame is located just under the zipper inside
the backpanel. To get to the frame simply run your fingers through the velcro that
connects the top flap. Once loose grap both side of the frame firmly whilst holding the
bottom of the pack with your feet and give the frame a small pull / pop up. Be sure to
note the orientation. Make sure it goes back in curved the same way, following the shape
of the shoulder straps and moving away from the body.
How do I remove the frame in the Adventure Pack?
Removing the frame in the Athlete Pack requires leverage. A tool such as a tire iron
works great. In a pinch the back of a knife or spoon. The frame on the Athlete Pack is
held in via a pressure flap located under the top lid. There is a slit in the tab that’s
designed to help you easily work in a tool that goes through the slot such that the fabric
rides up and the frame releases. Getting the frame back in requires the same set of
steps just in reverse. You should be able to get one side in by hand and need the tool for
the other side.
How do I remove the frame in the Athlete Pack?
It would take you a great deal of effort and energy and multiple attempts but yes, you
can damage / break a frame if you try hard enough. The frame will give before the pack
will. Replacement frames are available should you need.
Can I break the frame while removing / installing?
Yes. The key here is to have the supplies. A pipe cutter works best with the aluminum
but a Dremel or saw works too. The most important part is the heat shrink. It needs to
have an adhesive backing or risk slipping off and getting stuck inside the small sleeve
and it’s impossible to fish out.
Can I make the frame shorter DIY style?All about Airlines
The height of the frames is roughly the 1/2" or 1.25cm shorter than the height of the
packs.
What is the height of the frames?
The New Generation
Adventure Pack Fits!
Travel in 2022 and beyond is going to suck. Masks and middle
seats and ever shrinking legroom. When it comes to travel smaller
is better and now it's even easier to bring your Adventure Pack as
carry-on.
What if there is no more space in the overhead bins? The new
Adventure Pack will go under
the seat of most major carries. Take out your laptop and remove the
hip belt, frame and shoulder straps. Most airline seats have 9-10
inches of space, just enough for the Adventure Pack to squeeze into
in a pinch.
CABIN READYADVENTURE PACK
ORIGAMI CAMERA
CORE - TWO FOLD
If your camera gear looks like the photos on this page, you need an ORIGAMI CAMERA
CORE (TM). Clean, simple, elegant and quite, there's no velcro or magnets that make a
bunch of noise. For anyone that has not used an Atlas Pack before, our packs don't
have ICU's camera cubes or inserts like the other camera bag brands.
These systems are expensive and poorly designed. All of your camera
gear is detached from the structure of the bag and dependent on the
zippers to secure and hold your gear via a "pressure fit".
NO ICU OR CAMERA CUBES
In the Adventure Pack, the top 2/3 of the camera core now includes a
unique flexible section. This section can be positioned by the user to
shift space between the camping and camera section of the pack. Much
better than having to buy a bunch of different size inserts.
We call our solution the "ORIGAMI CAMERA CORE (TM)", inspired by the
Japanese art of paper folding. Each ORIGAMI CAMERA CORE (TM) is
designed and rated for specific types of camera gear. The rating on the
ORIGAMI CAMERA CORE (TM) has been given a huge boost. With two-
folds there is a ton of space that can be shifted between camping and
camera. A 50% increase over the single fold Adventure.
In the below illustration the camera section is highlighted in blue and
camping in white. The pack on the left is setup for the maximum
amount of camera and this amount decreases in the middle and third
pack. Each ORIGAMI fold has a little handle that you use the push and
pull on.
Can the frame be hand bend for better fit?
With an Atlas Pack your camera gear is fully accessible, easy to access and well secured.
NONE of these things are true when you use ICU's camera cubes or inserts. All of these
methods are insecure, result in a fundamental compromise to the packs' load carry
ability and result in poor workflow.
None of these complications are true with Atlas Packs. All Atlas Packs
are cabin sized to fit with frame in. Time to say goodbye to your old
ICU!
ORIGAMI CAMERA CORE (TM)
The ORIGAMI CAMERA CORE (TM) separates the Adventure Pack into a front section
(accessible from the top) for camping gear, and a back section (rear entry zipper) for
camera gear. In the very first photo the pack is setup for maximum camera gear. For the
new generation of packs, the Adventure Pack has a second fold and this bring me to the
next section...
SIMPLE PUSH AND PULL
CHANGE: Decreased exterior height of pack by 5cm / 2in. Exterior height now 24in / 61cm
with frame in. IMPACT: Brings the total volume of the Adventure Pack to 60+/- liters. Loss of
volume is not material to the usage of pack as most customer did not use the full 70 liter
shell. BENEFIT: Shorter is better. Users can expect to easily carry the Adventure Pack on
cabins and stow without having to remove the frame.
CHANGE: Complete redesign of ORIGAMI CAMERA CORE (TM) to now allows for second fold. IMPACT: Users can
now shift twice as much space between the camping and camera sections of the pack. BENEFIT: Users now have
up to 44 liters of volume for camping gear (up from 30 liters). That's a 50% increase in shiftable space.
CHANGE: Increased rating for the ORIGAMI CAMERA CORE (TM) by increasing friction and density. Added new types of foam,
changed the shaping of the foam (also called "skiving") and improved the outer fabrics that connect the Origami CC to the pack
and frame. IMPACT:The Origami Camera Core is able to handle the heavier weight of increased camping and/or camera gear.
BENEFIT: Users can expect to safely, securely and easily access and transport large sets of camera and/or camping gear.
NEW GENERATION UPDATES: DECREASED HEIGHT
SHIFT MORE SPACE
IMPROVED RATING
20 LITERS CAMERA | 30 LITERS CAMPING
This is the default setup for the Adventure
Pack and both Origami
folds are pushed in. This maximizes the
amount of camera gear you
can haul.I think it's fair to say that this
Adventure Pack will carry
more camera gear than most of us
own.With both of the Origami
folds pushed in, you get the full 20 liter of
camera space.And 30
liters of space for camping gear spread
around the rest of the pack.
13LITERS CAMERA | 37 LITERS CAMPING In
this second example the first Origami fold
has been pulled into
position and that volume has been
removed from the camera section
and shifted to the camping side.
6 LITERS CAMERA | 44 LITERS CAMPING In this
example both of the Origami folds have been
pulled out and
for me this is where the Adventure Pack gets
really interesting.In this
setup there is 44 liters for camping and 6 liters
for camera. I know 6
liters might not sound like a lot, but it is...
MAX CAMERA
BALANCED SETUP
MAX CAMPINGFor anyone carry big glass you will want the pack setup for max
camera. The Atlas Adventure camera pack includes an incredible
amount of storage for camera gear
With the Adventure Pack, big glass like the 400 2.8 and 200-600 can be
stored on bodies with hoods on and front lens caps off. This makes
workflow and organization so much easier. No other carry-on sized
camera bag that can do this >> and still leave you with lots of space to
pack non-camera gear. If you have
longer glass, 600mm and 800mm, these lenses can fit but eat up a lot
of room.
BIG GLASS
SONY KIT IN 2021 ADVENTURE PACK:+ Gripped Sony
Alpha + 400 2.8+ Gripped Sony Alpha + 200-600
......
THE ADVENTURE PACK SWALLOWS CAMERA GEAR
While the camera core does measure longer than these lenses, in real
world usage, glass longer than 17.5in / 43cm starts to push into the
top fold of the camera core. Why? When you get to the top end of the
measurements, there is a natural amount of wiggle room and flex.
Moreover, the packs measures and work differently based on the
objects you are storing. You can expect your pack to measure deeper
or shallower based on what you have on each side. Lots of small
lenses use space much better than one large telephoto down the
middle. Please use your judgement when setting up your pack.
ACCESS AND WORKFLOW
ADVENTURE PACK:+ Gripped Sony Alpha Kit with
Sony GM 200- 600, GM 16-35 2.8 GM + GM 24-70 2.8
GM + GM 100-400
......
Video equipment like a Canon C200 and the Sony FS5 can be stored
almost fully assembled. Typically only the LCD monitor needs to be
removed for storage.
VIDEO GEAR
2021 ADVENTURE PACK:+ Sony FS5 with Battery
Charger + Sony Alpha Bodies (x2), Sony GM 200-600,
GM 16-35 2.8 GM + GM 24-70 2.8 GM
.......
Gripped bodies easily fit in the Adventure Pack and can be stored in
any position. The depth of the ORIGAMI CAMERA CORE (TM) in the
Adventure Pack does not have a taper and you can expect your gear
to sit flush or below the line of the sidewalls and dividers.
As you can see from the images below (move the slider back and
forth), there is plenty of depth in the Adventure Pack for camera
bodies of all sizes.
GRIPPED BODIES EASILY FIT
ADVENTURE PACK:+ X2 Gripped bodies. Includes the
Canon R5 and Sony Alpha with grips plus a big
collection of Canon and Sony lenses
......
Trying to understand the difference between the Athlete and
Adventure Pack in terms of camera gear?In this next set of photos
we've taken the same kit (Canon R setup) in both.
In the Athlete Pack, you can see how much tighter the fit is and in
fact, there was not enough room for the some accessories. The
takeaway here is that with the Athlete Pack there are
accommodations you will need to make with how you setup and
organize your gear. These same limitations do not apply to the
Adventure Pack.
ATHLETE vs. ADVENTURE
CANON R5 KIT IN 2021 ATHLETE:+ Gripped Canon
R5 + 70-200+ Canon 15-35 2.8 R+ Canon 600mm
R+ Mavic Pro and Remote
.......
.n the Adventure Pack, you can see how the same set of gear plus a
little extra will fit in the bottom 2/3 of the ORIGAMI CAMERA CORE
(TM).
ADVENTURE vs. ATHLETE
CANON R5 KIT IN 2021 ADVENTURE PACK:+ Gripped
Canon R5 + 600mm+ Canon 15-35 2.8 R+ Canon 70-
200 2.8 R+ Mavic Pro and Remote+Gnarbox 2.0
......ADVENTURE PACK
HISTORY
3. An ORIGAMI CAMERA CORE, allowing the user to move a large volume of space to
either camera or without having to buy different inserts or camera cubes. And for all
camera
gear to be fully accessible without the zipper getting in the way.
What is the height of the frames?
The Adventure Pack was the first pack we designed. It 2014 and we
wanted to hit the ground with a pack designed exclusively for the
professional Photography and Video market.
Now as we all know, there are plenty of camera bag companies making
camera bags for this slice of the market. And as was true then, and is
still true today, none of these companies make camera bags that
properly load the weight of all that heavy gear to your hips.
Can the frame be hand bend for better fit?
4. Easy workflow, full access to camera gear without the zipper in the way and ample
space for non-camera gear. Fast forward through 5+ years and thousands of
conversations with happy customers about their Adventure Packs and you learn a lot
about what's working for who and why.
Thanks to this amazing feedback loop, we've made numerous updates to the
Adventure Pack over the years are are now taking a huge leap forward.
Why can’t Adventure frames be made shorter?
1. Include a hip belt to support and properly transfer the load of the
pack from the shoulders to the hips. If your camera bag has a sewn-in
hip belt, it will not properly transfer the
weight. Sewn-in hip belts twist and torque downwards under the
weight of the pack. They tend to dig into your sides due to lack of
padding and all of this means your shoulders are
doing the work. 2. A frame to support and anchor the weight onto the
hips and away from the shoulders. And for the frame to be easily
removable, along with hip belt and shoulder straps, to help
deal with ever changing carry-on restrictions.
What is the Travel frame for the large Athlete Pack?
Just as we did in when we first introduced the Adventure, we've built a pack
generations ahead of the market. We've made the pack smaller (carry-on with frame-
in), added more
room for camera gear (fits an 800mm) and added more room for camping gear (holds
up to 44 liters). Details regarding reservations as well as all of the updates and new
features
are below. Thanks for your support and interest. We love to chat and say hi. Please let
us know if you have any questions.
Cheers and thanks,
Allan [This page was update on DEC 27, 2022]
How do I remove the frame in the Adventure Pack?
In the Adventure Pack, the top 2/3 of the camera core now includes a unique flexible
section. This section can be positioned by the user to shift space between the camping
and camera section of the pack. Much better than having to buy a bunch of different size
inserts.
We call our solution the "ORIGAMI CAMERA CORE (TM)", inspired by the Japanese art of
paper folding. Each ORIGAMI CAMERA CORE (TM) is designed and rated for specific types
of camera gear. The rating on the ORIGAMI CAMERA CORE (TM) has been given a huge
boost. With two-folds there is a ton of space that can be shifted between camping and
camera. A 50% increase over the single fold Adventure.
In the below illustration the camera section is highlighted in blue and camping in white.
The pack on the left is setup for the maximum amount of camera and this amount
decreases in the middle and third pack. Each ORIGAMI fold has a little handle that you
use the push and pull on.
NEW GENERATION PACK
TWO-FOLD ADVENTURE PACK
ORIGAMI CAMERA CORE (TM)
This is a Canvify page. Please update the page from Canvify app.